Business Jet Tire Change & Wheel Inspection Guide
Business jet tire change and wheel inspection guide: removal criteria, pressure checks, safe demounting, wheel NDT, reassembly, 12-hour stretch and leak check.

· 8 min read · Aerotex International
A tire change looks like routine work, and on most business jets it is. But it’s also the moment when the wheel gets its closest inspection, when an O-ring or valve core that’s been in service for hundreds of landings gets replaced, and when a small mistake in torque, inflation or handling can cause a serious problem. Aircraft tire and wheel assemblies are inflated to high pressures, and both the FAA and the tire manufacturers warn that an inflated assembly can be dangerous if it’s handled incorrectly.
This guide walks maintenance managers and technicians through the main stages of an aircraft tire change and wheel inspection on a business jet or turboprop: when a tire should come off, how pressure checks work, safe removal and demounting, what the wheel inspection covers, reassembly, inflation and the post-mount leak check. It also explains when it makes more sense to swap the whole wheel assembly on exchange.
Important: This article summarizes FAA Advisory Circular 20-97B and published tire manufacturer guidance for general awareness. It is not a maintenance procedure. Always work to the current aircraft maintenance manual (AMM), the wheel component maintenance manual (CMM) and the tire manufacturer’s instructions, and follow your organization’s safety procedures.
When should a tire come off?
Wear and damage
FAA AC 20-97B lists conditions that should lead to a tire being removed from service, including:
- Tread damage: cracking or cutting in a tread groove that undercuts adjacent material, undercutting in a tread rib, or transverse cracks that progress down into the rubber
- Sidewall cuts that penetrate the outermost structural ply
- Bulges or distortions in the tread or sidewall that indicate internal separation
- Reverted or charred rubber above the wheel flange, from heat or slippage
- Wear or flat spots down to the outermost casing ply (bias tires) or outermost belt (radial tires)
The AC also recommends that tires subjected to unusual events, such as a high-energy rejected takeoff or a high-energy overspeed landing where the thermal fuse plugs released, be removed and scrapped. It cautions technicians not to probe cuts or embedded FOD while the tire is inflated.
Foreign object damage (FOD) is identified in the AC as the most common cause of premature tire removals.
Pressure loss
AC 20-97B recommends checking tire pressure daily with a calibrated gauge, ideally on “cold” tires (at ambient temperature, or at rest for at least two hours since the last flight). It gives these actions based on the loaded service pressure:
| Pressure found | AC 20-97B recommendation |
|---|---|
| 100–105% of service pressure | Normal range |
| 90–100% | Reinflate to the specified service pressure |
| Operated below 90% | Remove the assembly from service |
| Operated below 80% | Remove the assembly and its axle-mate from service |
Goodyear’s tire care manual uses a more detailed table (for example, it recommends inspecting for the cause of pressure loss at 95–100% and logging reinflation at 90–95%). Use the table in your AMM or the tire manufacturer’s manual for your aircraft.
Accurate inflation pressure is the most important part of tire maintenance, according to the AC, which calls it “the single-most effective task in the preventive maintenance regimen for safe tire operations.”
Removing the wheel from the aircraft
Follow the AMM for jacking, axle nut and bearing handling, brake and anti-skid connections, and any requirement to deflate before removal.
Before deflating a tire that was removed early, AC 20-97B recommends marking damaged areas so they can be found after deflation, and testing assemblies removed for pressure loss before demounting to find the cause. Goodyear also recommends checking the valve, fuse plugs and other leak points with soap solution before removing the tire.
Demounting the tire safely
The AC’s key points:
- Deflate completely before demounting. Remove the valve cap and valve core, and point the venting gas where it can’t harm anyone, since ice can form in the gas stream.
- Deflate the tire before loosening wheel tie bolts, following the wheel CMM and tire manufacturer’s instructions.
Mounting and demounting aircraft tires is specialized work best done with the right equipment and trained people, Goodyear says.
Inspecting the wheel at a tire change
The tire change is when the wheel halves are accessible, so it’s the natural time to inspect them. The CMM for your wheel sets the requirements. For example, APSS’s CMM-based outlines for the Learjet 40/45 main wheel (3-1545-1) and the Legacy 600/650 nose wheel (3-1551) call for eddy current/NDT at every tire change. Typical inspection points include:
- Cracks, especially in the bead seat area, usually found with eddy current inspection
- Corrosion, including under paint and around bolt holes
- Bearings, bearing cups and bores: wear, damage, corrosion and correct lubrication
- O-ring grooves and sealing surfaces
- Thermal (fuse) plugs: signs of melting or release, which can indicate the wheel overheated
- Overinflation (pressure relief) plug condition
- Tie bolts and nuts: condition and replacement requirements per the CMM
- Valve body and threads
Wheels that fail inspection may need repair or overhaul, or may be condemned. APSS notes, for example, that a 3-1545-1 that needs penetrant inspection is processed as an overhaul. If you’re running wheels on exchange, these findings drive whether a core is repairable. See Core Charges, Core Returns and BER Explained.
For aircraft-specific wheel details, see our 3-1545-1 Learjet 45 main wheel and 9544207 Learjet nose wheel pages, the Legacy 600/650 guide and the PC-12 guide.
Reassembly
Key points from AC 20-97B and Goodyear’s tire care manual:
- Confirm the tire, wheel and valve are correct for the application. Check the tire part number against the IPC and wheel CMM.
- Clean the wheel and make sure it’s free of burrs or roughness. Goodyear recommends cleaning the bead seat with a cloth dampened with denatured alcohol.
- Install a new O-ring of the correct part number at each tire change, using the wheel manufacturer’s lubricant instructions.
- Inspect the valve and install a new valve core.
- Align the tire’s red balance dot with the wheel valve or the wheel’s heavy point, if marked. Goodyear explains what to do if there’s no dot.
- Torque tie bolts to the wheel manufacturer’s instructions before inflating, and use the CMM’s torque pattern.
For tube-type tires, the AC and Goodyear call for a new tube when installing a new tire.
Inflation and the 12-hour stretch
- Inflate in a safety cage, using a clip-on chuck and extension hose.
- Use dry nitrogen. The AC says initial inflation of tubeless tires should be done with dry nitrogen so the tire contains no more than 5% oxygen by volume. (14 CFR 25.733 requires inert-gas inflation for braked-wheel tires on transport category airplanes over 75,000 lb maximum takeoff weight, with some exceptions. Many lighter business jets fall below that threshold, but check your AMM.)
- Set the regulator to no more than the maximum the tire is rated for. Goodyear says to regulate the supply to no more than 50% above service pressure, and never inflate above rated pressure to seat the beads.
- Allow for stretch. New tires grow after initial inflation, which lowers pressure. The AC says stabilization normally happens within 12 hours.
The 24-hour leak check
After a minimum 12-hour stabilization period at rated pressure, AC 20-97B says the tire should hold pressure within 5% of the initial pressure for 24 hours. If it loses more than that, find and fix the leak. Goodyear lists the usual suspects: the valve, valve core and seal, fuse plugs, pressure release plug, O-ring and the wheel itself.
Two points the AC makes about leak checks:
- Temperature affects results. A ±5°F change in the assembly alters gauge pressure by about 1%, so record the ambient temperature at the start and finish.
- Bubbling from sidewall vent holes on tubeless tires after initial inflation is normal and doesn’t by itself mean the assembly is leaking.
In-shop tire change or exchange wheel assembly?
A tire change and wheel inspection takes time, including the stretch period and leak check. Many operators keep a spare wheel assembly or order a built-up, inspected assembly (“axle-ready”) on exchange to cut downtime, especially away from base. Duncan Aviation is another shop you may come across when ordering a wheel assembly on exchange. When buying a wheel assembly, confirm:
- Wheel P/N and dash number match the IPC
- Tire part number and whether it’s new or retreaded (check your operator policy on retreads)
- Release paperwork. An FAA Form 8130-3 normally covers the wheel work. See FAA 8130-3 Tag Explained.
- Condition: OH or SV. See Aircraft Part Condition Codes.
- How it’s shipped, including whether it’s inflated
Frequently asked questions
How often should business jet tire pressure be checked? FAA AC 20-97B recommends daily checks with a calibrated gauge, ideally on cold tires. Follow your AMM.
Should aircraft tires be inflated with nitrogen? The FAA advisory circular recommends dry nitrogen for initial inflation. Transport category airplanes over 75,000 lb are required to use inert gas for braked-wheel tires under 14 CFR 25.733. Check your AMM for your aircraft.
What should be replaced at every tire change? The AC and Goodyear call for a new O-ring and a new valve core at each tire change. The wheel CMM may require other parts too.
Is wheel NDT required at every tire change? It depends on the wheel CMM. For some business jet wheels, such as the Learjet 40/45 3-1545-1, published CMM-based outlines call for eddy current/NDT at every tire change.
How long does a new tire need before it goes back in service? The AC describes a minimum 12-hour stabilization period, then a 24-hour pressure retention check, unless the AMM or CMM says otherwise.
When must the axle-mate tire also be removed? Per AC 20-97B, when a tire was operated below 80% of its minimum loaded service pressure.
Related reading
- 3-1545-1 Learjet 45 Main Wheel
- 9544207 Learjet Nose Wheel
- Learjet 40/45/75 Wheels & Brakes Guide
- Pilatus PC-12 Wheels, Brakes & Parts Exchange Guide
- Aircraft Brake Wear Pin Inspection
- Core Charges, Core Returns and BER Explained
- AOG Aircraft Parts in Dallas–Fort Worth
Need a wheel assembly on exchange?
If a tire change turns into a condemned wheel, or you’d rather swap the whole assembly, send us the wheel part number, tire preference and condition you need.
Taylor Mason, VP of Sales, Aerotex International
Phone: 469-293-3311 · Email: tmason@aerotex.net
For AOG orders, call 469-293-3311 directly.
For reference only. Always confirm part eligibility and procedures against the current IPC/CMM and your maintenance provider. This guide is general information, not regulatory advice. Always follow your approved maintenance data, your quality system and your regulator’s current guidance.
Need a part? Search by part number or send an RFQ.
