FAA 8130-3 Tag Explained: What It Certifies and How to Read It
FAA 8130-3 tag explained for parts buyers: what the form certifies, what Block 11 terms mean, dual release, the 2025 FAA guidance update and red flags to check.
· 8 min read · Aerotex International
If you buy overhauled wheels, brakes or rotables, you’ll see an FAA Form 8130-3 with almost every part. Most people call it an “8130 tag”, file it with the work order, and move on. But the 8130-3 says much more than “this part is good.” It tells you who released the part, under what authority, what work was done, to what standard, and whether it’s acceptable in Europe as well as the US. It also doesn’t say some things that many buyers assume it does.
This guide explains the FAA 8130-3 in plain terms: what it’s for, what it can’t be used for, how to read each block, what the Block 11 status terms mean, and the red flags to watch for.
Important: This article summarizes FAA guidance as of October 2026, cited at the end. It isn’t a substitute for the FAA documents or your own quality procedures.
What is FAA Form 8130-3?
The full name is FAA Form 8130-3, Authorized Release Certificate, Airworthiness Approval Tag. According to the FAA’s 8130-3 FAQ, the form has several purposes:
- It can be a statement that a new product or article produced under 14 CFR part 21 conforms to its design and is in a condition for safe operation.
- It can be used to return a used product or article to service after inspection, maintenance or alteration.
- It can be used for export under bilateral agreements.
- In all cases, it promotes identification and traceability of parts throughout the aviation system.
For business jet parts buyers, the most common case is the second one: a repair station overhauls, repairs or inspects a wheel, brake or rotable and releases it with an 8130-3.
What the 8130-3 does not do
The FAA’s FAQ and its current advisory circular are clear on these points:
- It isn’t approval to install the part on a particular aircraft, engine or propeller. It helps you establish the part’s airworthiness status, but installation eligibility is still determined from the IPC, type design and your maintenance data. See How to Read an IPC and CMM to Find Interchangeable Part Numbers.
- It isn’t a shipping or delivery document, and shouldn’t be used for administrative purposes between two parties.
- It can only be issued by persons the FAA has authorized, within the scope of that authorization.
- It isn’t used to release whole aircraft.
- A maintenance-release 8130-3 can’t be issued for articles without design approval.
The 2025 update: where FAA guidance now lives
For years, instructions for completing the form for both production and maintenance were in FAA Order 8130.21H. In September 2025 the FAA split them:
- FAA Order 8130.21J (issued September 25, 2025) covers completing the form under part 21, for new production, conformity, export and authorized release documents.
- AC 43-9D, Maintenance Records and FAA Form 8130-3 Return to Service (issued September 22, 2025, with an editorial update dated April 30, 2026) now contains the instructions for using the form to approve return to service after maintenance under 14 CFR part 43.
If your receiving inspection procedures still cite Order 8130.21H for maintenance releases, they’re due for an update.
How to read an 8130-3, block by block
The form has 14 numbered blocks. Blocks 13a–13e are used for part 21 releases (new parts, export). Blocks 14a–14e are used for maintenance return to service. You’ll normally see only one side completed.
| Block | What it shows | What to check |
|---|---|---|
| 1 | Approving authority / country (“FAA/United States,” preprinted) | |
| 2 | Form title (preprinted) | |
| 3 | Form tracking number | A unique number from the issuer. Useful if you need to verify the form with them. |
| 4 | Organization name and address | The issuing organization, its physical address and its certificate number (for example, a repair station certificate number). Make sure it’s real and matches who you bought from or who did the work. |
| 5 | Work order / contract / invoice number | Links the form to the issuer’s records. |
| 6 | Item | Item number(s) on the form. |
| 7 | Description | Should use the name from the IPC or maintenance data. |
| 8 | Part number | Must match the part’s data plate exactly, including dash number. |
| 9 | Quantity | |
| 10 | Serial number | Must match the data plate. A mismatch is a reason to stop. |
| 11 | Status/Work | What the form certifies (see below). |
| 12 | Remarks | The work performed, the data used (for example, the CMM and revision), ADs and SBs complied with, dual release statements and other details. |
| 13a–13e | Part 21 airworthiness approval | Used for new parts and export releases. |
| 14a–14e | Maintenance return to service | Box(es) checked, signature, certificate number, name and date. |
Block 11: what the status terms mean
For a maintenance release, AC 43-9D lists these Block 11 terms:
- OVERHAULED – the most demanding term. The article is brought into complete conformity with the service tolerances in the manufacturer’s instructions for continued airworthiness or other approved or accepted data. At a minimum it’s disassembled, cleaned, inspected, repaired as necessary, reassembled and tested.
- REPAIRED – a defect has been repaired using an applicable standard.
- INSPECTED and/or TESTED – the article has been examined or measured to an applicable standard (for example, visual inspection, functional test or bench test).
- MODIFIED – the article has been altered to conform to an applicable standard.
The applicable standard has to be described in Block 12.
For new parts released under part 21, Block 11 typically shows NEW (and, for certain cases, terms like PROTOTYPE, or USED for export). Check the current FAA Order 8130.21 for the full list of terms.
Why it matters for buyers: an “8130-3 overhauled wheel” and an “8130-3 inspected/tested wheel” are not the same product. If you paid for an overhauled (OH) unit, Block 11 should say OVERHAULED. Our Aircraft Part Condition Codes guide explains how Block 11 relates to the OH/SV codes you see on listings.
Block 12: read it every time
Block 12 is where the detail lives. For a wheel or brake overhaul, expect to see:
- The CMM reference and revision used, for example a Collins/Goodrich CMM number for a Learjet 45 main wheel (see our 3-1545-1 page)
- ADs and service bulletins complied with, where applicable
- Parts replaced, or a reference to an attached work order
- Dual release statement, if the part was also released for EASA
AC 43-9D also says Block 12 (or an attachment) must clearly document the work process. Vague remarks are a reason to ask questions.
Dual release: FAA and EASA
If your aircraft is EU-registered or you sell parts into Europe, you may need a dual release. Under the US–EU bilateral arrangements, a qualifying repair station can return a part to service for both authorities on one 8130-3. Per AC 43-9D, both boxes in Block 14a are checked (“14 CFR 43.9 Return to Service” and “Other regulation specified in Block 12”), and Block 12 carries a specific EASA certification statement. The FAA’s FAQ notes that a part returned to service with a dual release 8130-3 is eligible for installation on US- or EU-registered aircraft. Not every repair station can issue a dual release, so ask before you order.
8130-3 for new parts
A new part doesn’t always come with an 8130-3. The FAA’s FAQ explains that the form can be issued for new parts only in specific circumstances, such as while the part is still within the production approval holder’s quality system, or through an authorized designee who establishes airworthiness and traceability to the production approval holder. A new part from a distributor may instead come with a manufacturer’s certificate of conformity and trace documents. Know what your maintenance program requires for new parts.
Red flags on an 8130-3
- Part number or serial number doesn’t match the data plate
- Block 4 names an organization you can’t verify, or has no certificate number
- Block 11 says less than you paid for (for example INSPECTED/TESTED when you bought OH)
- Block 12 gives no data reference or revision
- Block 14 is unsigned, undated or missing the certificate number
- The form is a copy not marked as a copy, or shows signs of alteration
- The form arrives separately from the part. The FAA says forms shouldn’t be delivered before the part ships and should be correlated with the shipment.
If something looks wrong, quarantine the part and contact the issuer using the tracking number in Block 3. The FAA asks that suspected unapproved parts be reported under AC 21-29.
Frequently asked questions
What does an 8130-3 tag mean? It’s the FAA’s Authorized Release Certificate. It documents a part’s airworthiness status, either as a new part produced under FAA approval or as a used part returned to service after maintenance, and supports traceability.
Does an 8130-3 mean I can install the part on my aircraft? No. The FAA says the form doesn’t constitute approval to install on a particular aircraft. Check eligibility in the IPC and your maintenance data.
What’s the difference between “overhauled” and “inspected/tested” on an 8130-3? Overhauled means the part was disassembled, cleaned, inspected, repaired as needed, reassembled and tested to approved data. Inspected/tested means it was examined or tested to a standard, without a full overhaul.
Who can issue an 8130-3? Only persons the FAA has authorized, such as certificated repair stations for maintenance releases or production approval holders and designees for new parts, within the scope of their authorization.
What is a dual release 8130-3? An 8130-3 that returns a part to service for both the FAA and EASA, with both boxes checked in Block 14a and the EASA statement in Block 12.
Is the 8130-3 the same as an EASA Form 1? They’re equivalent documents from different authorities and use the same block layout, but the completion instructions differ in places.
Related reading
- Aircraft Part Condition Codes
- 3-1545-1 Learjet 45 Main Wheel
- Learjet 40/45/75 Wheels & Brakes Guide
- Core Charges, Core Returns and BER Explained
- How to Source Business Jet Parts Fast
- How to Read an IPC and CMM to Find Interchangeable Part Numbers
- Sell Surplus Aircraft Parts
Questions about paperwork on a part you need?
Ask us what release paperwork ships with any part we quote, before you order.
Taylor Mason, VP of Sales, Aerotex International
Phone: 469-293-3311 · Email: tmason@aerotex.net
For AOG orders, call 469-293-3311 directly.
For reference only. Always confirm part eligibility and procedures against the current IPC/CMM and your maintenance provider. This guide is general information, not regulatory advice. Always follow your approved maintenance data, your quality system and your regulator’s current guidance.
Need a part? Search by part number or send an RFQ.
