Skip to content
Aerotex International logo

Resources / Explainers

How to Read an IPC and CMM to Find Interchangeable Part Numbers

How to read an aircraft IPC and CMM to find interchangeable part numbers: effectivity, alternate and superseded P/Ns, interchangeability codes and STC pitfalls.

· 8 min read · Aerotex International

“Is this one interchangeable?” is one of the most common questions in aircraft parts buying, and one of the most expensive to get wrong. A part can share most of its part number with yours, come from the same manufacturer, and even fit physically, and still not be approved for your aircraft. On the other hand, a part listed under a completely different number may be exactly what you need, because it’s the airframe manufacturer’s number for the same component.

The answers are in two documents: the airframe manufacturer’s Illustrated Parts Catalog (IPC) and the component manufacturer’s Component Maintenance Manual (CMM). This guide explains how each one is organized, how to read effectivity and interchangeability information, how alternate and superseded part numbers work, and where STCs, service bulletins and PMA parts fit in.

Important: IPC layouts, column names and interchangeability codes differ between manufacturers and revisions. Always read the introduction (front matter) of your specific IPC and use the current revision. Part numbers used as examples below come from published listings cited at the end, not from an OEM IPC.

IPC vs CMM: who publishes what

Illustrated Parts Catalog (IPC) Component Maintenance Manual (CMM)
Published by The airframe manufacturer (e.g., Bombardier, Embraer, Pilatus) The component manufacturer (e.g., Collins/Goodrich, Parker Meggitt, Cleveland)
Covers The whole aircraft, broken down by system One component or family (e.g., a main wheel or brake)
Tells you Which part numbers are approved at each position on your aircraft, by serial number How to inspect, repair, overhaul and test the component, plus its own illustrated parts list
Use it to Decide what you’re allowed to install Understand the component’s internal parts and repair

Both are usually organized by ATA chapter. Wheels and brakes are in ATA chapter 32 (landing gear). That’s why wheel and brake CMM numbers often look like 32-xx-xx. For example, shops list the Learjet 40/45 main wheel 3-1545-1 under CMM 32-48-72 and the Legacy 600/650 nose wheel 3-1551 under 32-49-04.

The rule of thumb: the IPC decides eligibility on your aircraft. The CMM governs the component itself. A CMM won’t tell you whether a part fits your aircraft serial number.

How an IPC entry is laid out

Most IPCs present each assembly as a figure (an exploded illustration) with a parts list next to it. Typical columns include:

  • Figure and item number: ties the part list to the illustration
  • Part number: the approved part number(s) for that item
  • Nomenclature or description, often indented to show the assembly hierarchy (an indented item is part of the item above it)
  • Effectivity or usable-on code: which aircraft serial numbers, models or configurations the line applies to
  • Units per assembly
  • Vendor or supplier code, often a CAGE code identifying the manufacturer

Column names vary by manufacturer, so check the introduction to your IPC.

Step 1: Start with effectivity

Effectivity is the first filter. The same position on two aircraft of the same model can call for different part numbers depending on:

  • Aircraft serial number range
  • Model variant (for example Learjet 40 vs 45 vs 75, or Legacy 600 vs 650)
  • Service bulletin or modification status
  • Installed STCs

Our Learjet 40/45/75 guide and 3-1545-1 page show how this plays out: published shop listings disagree on whether the 3-1545-1 main wheel applies to the Learjet 75, which is exactly the kind of question only the IPC for your serial number can settle.

Step 2: Identify every valid number for the part

A single component often has more than one valid part number:

  • Vendor (component manufacturer) part number, e.g., the Goodrich 3-1545-1 main wheel
  • Airframe manufacturer part number for the same item, e.g., 66324010000-001, listed by distributors as the alternate for the 3-1545-1
  • Other examples: the Legacy 600/650 nose wheel 3-1551 is listed with Embraer-format alternate 145-26082-401 (see our 3-1551 page); the PC-12 Goodrich brake 2-1674-1 is listed in a Cleveland document as Pilatus P/N 959.56.01.512

The IPC usually shows the relationship between these numbers. When you search marketplaces, search all of them. Sellers list under whichever number is on their paperwork. See How to Source Business Jet Parts Fast.

Step 3: Read the interchangeability information

When a part number changes, for example through a design improvement or a service bulletin, the IPC or the manufacturer’s data indicates how the old and new numbers relate. The ATA Spec 2000 data standard defines interchangeability codes along these lines:

Code (Spec 2000) Meaning
1 One-way interchangeable: the new part can replace the old, but not the other way around
2 Two-way interchangeable: either can replace the other
3 Not interchangeable
4 Interchangeable as a set: must be changed together with related parts
5 Qualified interchangeability: interchangeable only under stated conditions
6 Part reidentification (provisioning data)

Airframe IPCs don’t all use these numeric codes. Some use letters, notes or symbols. Some show “optional” or “alternate” parts in a separate column. Some put the information in service bulletins rather than the IPC. Use the legend in your IPC’s introduction.

One-way interchangeability is the trap. If a new dash number replaces an old one one-way, you can install the new part where the old one was, but you can’t put the old part back once the new one is installed, and you may not be able to accept an old-dash-number unit on exchange. That’s why wheel and brake dash numbers deserve careful checking. See, for example, the Legacy 2-1699-2 vs -3 brake question and the Learjet 5003096-series brakes.

Step 4: Check service bulletins and supersession

A part number can be superseded through a component manufacturer’s service bulletin, the airframe manufacturer’s service bulletin, or both. Before accepting a part:

  • Check whether component SBs change the part number or require modification, and whether they’re mandatory for your operation
  • Check whether an airworthiness directive applies to the part number or serial range
  • Check the modification status on the data plate. Some exchange terms require the core to match the mod status of the unit you received.

Step 5: Know what the IPC won’t tell you

STC-installed parts

Parts installed under a supplemental type certificate aren’t IPC alternates. They’re a different approved configuration. The Pilatus PC-12 is a good example: the Cleveland 40-424 wheel and 30-244 brake are installed under STC SA01376CH using a conversion kit, which can also require brake pedal lever changes depending on serial number and service bulletin status. A Cleveland brake isn’t “interchangeable” with the Goodrich brake in the IPC sense. You either have the STC configuration or you don’t. See our PC-12 guide.

For an STC-modified aircraft, the STC holder’s documents (installation instructions, ICA, any IPC supplement) control the parts for that installation.

PMA parts

Parts made under a Parts Manufacturer Approval (PMA) are FAA-approved replacement parts, but they may carry the PMA holder’s part number. Whether a PMA part is eligible for your aircraft is shown by the PMA’s eligibility, not by the airframe IPC. Your operator’s policy may also restrict PMA use.

Physical fit doesn’t mean approval

The FAA’s guidance on parts eligibility (AC 20-62E) puts the responsibility on the installer to make sure a part is eligible and airworthy. A part that bolts on isn’t necessarily approved, and an 8130-3 doesn’t make it so either. See FAA 8130-3 Tag Explained.

Using the CMM when buying wheels and brakes

The CMM matters when you buy overhauled components because:

  • Block 12 of the 8130-3 should cite the CMM and revision used for the work. If it doesn’t, ask.
  • The CMM’s illustrated parts list shows internal parts, such as heat stack components, bearings, seals and fuse plugs, which helps you understand overhaul quotes.
  • The CMM sets repair and overhaul limits, which decide whether a core is repairable or BER. See Core Charges, Core Returns and BER Explained.
  • The CMM may list optional or alternate subassemblies within the component, which don’t change the component’s top-level part number.

A quick interchangeability checklist

  1. Find the part’s position in the IPC figure for your aircraft.
  2. Filter by effectivity for your serial number and configuration.
  3. List every approved part number for that position, including vendor and airframe numbers.
  4. Read the interchangeability code or note for each, using your IPC’s legend.
  5. Check SBs, ADs and mod status.
  6. Check for STCs on your aircraft that change the configuration.
  7. When the part arrives, confirm the data plate, 8130-3 and IPC all agree.

Frequently asked questions

What’s the difference between an IPC and a CMM? The IPC comes from the airframe manufacturer and shows which part numbers are approved on your aircraft. The CMM comes from the component manufacturer and covers inspection, repair and overhaul of that component.

What does one-way interchangeable mean? The newer part can replace the older one, but the older part can’t replace the newer one.

Is an alternate part number the same part? Often it’s the same component listed under the airframe manufacturer’s number, such as 66324010000-001 for the 3-1545-1 main wheel. Confirm in the IPC before treating any alternate as interchangeable.

Can I install a part with a different dash number? Only if your IPC or applicable service data says it’s interchangeable for your aircraft serial number.

Are STC parts listed in the IPC? Usually not. STC parts are controlled by the STC holder’s documents, and they represent a different configuration rather than an IPC alternate.

Related reading

Not sure which part number you need?

Send us the part number from your data plate, your aircraft serial number and the IPC reference if you have it. We’ll quote the part number you specify; final eligibility is confirmed against your IPC.

Taylor Mason, VP of Sales, Aerotex International
Phone: 469-293-3311 · Email: tmason@aerotex.net
For AOG orders, call 469-293-3311 directly.

For reference only. Always confirm part eligibility and procedures against the current IPC/CMM and your maintenance provider. This guide is general information, not regulatory advice. Always follow your approved maintenance data, your quality system and your regulator’s current guidance.

Need a part? Search by part number or send an RFQ.

AOGGrounded?