Learjet 40/45/75 Wheels & Brakes Guide: Part Numbers, Exchange Options and AOG Sourcing
Learjet 45 brake assembly and wheel guide for LJ40/45/75 operators: part numbers, inspection basics, exchange vs. overhaul options and how to source AOG parts.
· 9 min read · Aerotex International
When a Learjet 45 brake assembly reaches its wear limit or a main wheel fails an inspection, the aircraft stays on the ground until a serviceable unit shows up. This guide is for maintenance directors, chief pilots and parts buyers who look after Learjet 40, 45 and 75 aircraft. It covers the main wheel and brake part numbers you’ll come across, what happens to wheels and brakes in the shop, the ways to buy a replacement, and what to check on the paperwork before you install anything.
Important: Part numbers and fitment in this article come from published MRO and distributor listings, cited at the end. Always confirm effectivity for your serial number in the current Bombardier Illustrated Parts Catalog (IPC) and the component maintenance manual (CMM) before you order or install.
Learjet 40/45/75 wheel and brake part numbers at a glance
The Learjet 40, 45 and 75 share one landing gear family. Several wheel and brake shops list the same main wheel and brake part numbers for all three models. The table below sums up what published sources show.
| Component | Part number | Alternate P/N | Manufacturer | Listed fitment | CMM ref. (per shop listings) |
|---|---|---|---|---|---|
| Main wheel assembly | 3-1545-1 | 66324010000-001 | Goodrich (now Collins Aerospace) | Learjet 40, 45 (some shops also list the 75; confirm in your IPC) | 32-48-72 |
| Brake assembly (carbon) | 2-1579-2 | — | Goodrich (now Collins Aerospace) | Learjet 40, 45 (some shops also list the 75; confirm in your IPC) | 32-48-71 |
| Nose wheel assembly | 9544207-4 | 2342003-077, 9544207-5 | Meggitt Aircraft Braking Systems | Learjet 40, 45 (also listed for other Learjet models; confirm dash number in your IPC) | 32-46-14 |
Some notes on the table:
- 3-1545-1 main wheel. ASI and Proserv Aviation list it for the Learjet 40 and 45. World Aero and APSS also list it for the Learjet 75. Proserv gives the alternate part number 66324010000-001 and a tire size of 22 x 5.75-12. We have a dedicated page on the 3-1545-1 main wheel with more detail.
- 2-1579-2 brake. ASI calls it a carbon brake assembly for the Learjet 45 and 40. World Aero lists it for the Learjet 40, 45 and 75, and Textron Aviation’s parts catalog also carries it as a “brake assembly.”
- Nose wheel. Distributor listings give the Meggitt 9544207-4 as a Learjet 40/45 nose wheel, with alternates 2342003-077 and 9544207-5. Check dash-number interchangeability in your IPC before you accept an alternate.
Wheels and brakes for older Learjets, such as the 5003096-series brakes on the Learjet 25/35 and 55/60, are a different family. They do not interchange with the Learjet 40/45/75 parts above.
How Learjet 45 wheels and brakes are maintained
Wheels and brakes are rotable components. They come off the aircraft, go through a shop, get certified and go back into service, often on another aircraft. Knowing what the shop does to them helps you read quotes and paperwork.
Main wheels: tire changes, NDT and overhaul
APSS publishes a maintenance outline for the 3-1545-1 based on the CMM. It calls for eddy current/NDT inspection at every tire change, added inspections at each third tire change, and an overhaul if penetrant inspection is needed. At a tire change, the tire, wheel-half O-ring, valve cap and valve core are normally replaced. An overhaul goes further and covers seals, the overinflation plug and the thermal relief (fuse) plugs. The governing intervals and limits are in the Collins/Goodrich CMM, so ask your shop which revision they worked to.
Wear points to watch on main wheels include bearings, O-ring grooves and corrosion. A wheel that fails NDT or has cracks beyond CMM limits gets condemned instead of repaired. That’s one reason exchange terms often say what happens when a core is “beyond economical repair.”
Brakes: wear pins, heat stack and overhaul
Like most carbon brakes, the Learjet 45 brake has a wear indicator that shows how much heat-sink material is left. Technicians check it during routine inspections. When the indicator reaches the limit in the aircraft maintenance manual, the brake comes off for overhaul or exchange. The actual wear-pin limits and inspection method are in the Bombardier AMM and the brake CMM.
A brake overhaul usually includes disassembly, inspection of the housing and pistons, heat stack (carbon disc) replacement or refurbishment, seal replacement, and a pressure and leak test. ASI’s 2-1579-2 listing offers the brake with or without a heat stack, which affects price. When you compare quotes, make sure you’re comparing the same scope.
Carbon brakes and why it matters for budgeting
Since the 2-1579-2 is a carbon brake, the heat stack is often the biggest single cost driver in an overhaul. How long a carbon brake lasts depends a lot on how the aircraft is flown: number of landings, taxi habits and stop energy. Two operators with the same airframe can see very different brake life. If you’re planning a maintenance budget, track wear-pin readings over time instead of relying on a generic “landings per brake” figure.
Ways to replace a Learjet 45 brake assembly or wheel
When a wheel or brake is due, operators usually have four options. Each has its own trade-off between downtime and cost.
1. Exchange
You get an overhauled or serviceable unit now and send your removed unit (the “core”) back. It’s the fastest way to get back in the air. Most of the Learjet 45 wheel and brake listings we reviewed are sold on exchange. ASI, for example, sells its 3-1545-1 and 2-1579-2 units “on exchange only, and with standard terms.” Duncan Aviation is another source you may come across when shopping for these units on exchange. Exchange comes in several forms:
- Standard exchange: an exchange fee that covers a set amount of repair work. Anything above that is billed as “over and above” (O&A).
- Flat-rate exchange: one upfront price that includes the repair of your core, apart from defined exceptions such as a beyond-economical-repair (BER) core. See Flat-Rate Exchange Explained.
- Cost-plus exchange: a lower upfront fee, with the actual repair cost of your core billed later.
2. Outright purchase
You buy the unit and keep it, and there’s no core to return. Outright costs more upfront. It makes sense when you don’t have a core, when you want a spare on the shelf, or when your core is likely to be BER.
3. Overhaul your own unit
You send your wheel or brake to a repair station and wait for it to come back. This is often the lowest direct cost, but the aircraft sits (or flies on a spare) the whole time. It works best for planned maintenance or for operators who already keep a spare.
4. Loan or rental
Some suppliers offer short-term loans while your own unit is overhauled. Availability and terms vary widely by supplier.
For a side-by-side look at how these options compare on cost and risk, read Exchange vs Outright vs Overhaul: Cost Guide.
What to check before you install
Whoever you buy from, check these points before the part goes on the airplane.
- Part number and dash number match the IPC for your aircraft serial number. Don’t assume an alternate P/N is interchangeable without checking the IPC or a service bulletin.
- Release documentation. Overhauled parts from a US repair station usually come with an FAA Form 8130-3, the Authorized Release Certificate. According to the FAA, the form can be used to return a used article to service after maintenance, and it helps with traceability. It is not approval to install the part on a particular aircraft. Installation eligibility is still your responsibility. Dual-release (FAA/EASA) paperwork may matter if you operate outside the US.
- Work performed. The 8130-3 remarks block or the attached work order should say what was done (overhaul, repair, inspection/test) and which CMM revision was used.
- Condition code. Learn how your supplier uses terms like NE (new), OH (overhauled), SV (serviceable) and AR (as removed). They aren’t interchangeable, and they affect price and remaining life.
- Heat stack and wear status for brakes, and the tire part number and whether the tire is included for wheels. Proserv’s 3-1545-1 listing, for example, specifies a Goodyear Flight Eagle 226K08-4 tire.
- Core return terms if you’re buying on exchange: how many days you have, what condition the core must be in, and what happens if it’s BER.
Sourcing AOG Learjet parts
An AOG (aircraft on ground) event on a Learjet 45 is usually a wheel or brake that can’t wait for a planned overhaul. A few habits make AOG sourcing faster:
- Have the exact P/N and serial number ready, and a photo of the data plate if you can. Many delays come from part-number confusion.
- Check the online marketplaces. Learjet wheels and brakes are widely listed on ILSmart and PartsBase, where Aerotex also lists inventory.
- Ask about paperwork upfront. Confirm that the 8130-3 (and any dual release you need) will ship with the part, not after it.
- Agree on core terms before the part ships, so an AOG purchase doesn’t turn into a billing dispute later.
Aerotex International is based in Lewisville, Texas, in the Dallas–Fort Worth area, and has supplied parts to business jet operators since 1994.
Frequently asked questions
What is the brake assembly part number for a Learjet 45? Published MRO and distributor listings identify the Goodrich (now Collins Aerospace) 2-1579-2 carbon brake assembly for the Learjet 40 and 45, and some list it for the Learjet 75 as well. Always confirm against the IPC for your serial number.
Is the Learjet 45 main wheel the same as the Learjet 40 and 75? Several wheel shops list the 3-1545-1 main wheel for the Learjet 40, 45 and 75. Some distributors list only the 40 and 45. Check the IPC for your aircraft before you order.
What is the alternate part number for the 3-1545-1? Proserv Aviation and APSS list 66324010000-001 as the alternate part number for the 3-1545-1 main wheel.
How do I know when my Learjet 45 brakes need replacing? The brake wear indicator is checked during inspections. The brake is removed when wear reaches the limit in the aircraft maintenance manual. Use the current AMM and CMM for the actual limits.
Is it cheaper to exchange or overhaul a Learjet 45 brake assembly? Overhauling your own unit is often the lowest direct cost, but the aircraft is down while it’s in the shop. Exchange costs more upfront and gets you flying sooner. Your best choice depends on your schedule, whether you keep a spare and how good your core is.
Does an 8130-3 tag mean a part can be installed on my aircraft? No. The FAA says Form 8130-3 does not constitute approval to install the part on a particular aircraft. It documents airworthiness status and traceability. Eligibility is confirmed through the IPC and your maintenance data.
Related reading
- 3-1545-1 Learjet 45 Main Wheel: Specs, Alternate Part Number, Exchange
- Flat-Rate Exchange Explained
- Exchange vs Outright vs Overhaul: Cost Guide
- Embraer Legacy 600/650 Wheel & Brake Part Number Guide
Get a quote or AOG support
Need a Learjet 45 brake assembly, a 3-1545-1 main wheel or other Learjet 40/45/75 parts? Send us the part number, condition you need and whether you want exchange or outright, and we’ll quote it.
Taylor Mason, VP of Sales, Aerotex International
Phone: 469-293-3311 · Email: tmason@aerotex.net
For AOG orders, call 469-293-3311 directly.
For reference only. Always confirm part eligibility and procedures against the current IPC/CMM and your maintenance provider. This guide is general information, not regulatory advice. Always follow your approved maintenance data, your quality system and your regulator’s current guidance.
Need a part? Search by part number or send an RFQ.
